(Click the banner above if you do not see a navigation menu to the left)

Eyepiece Accessories

ScopeTronix Parfocalizing Rings

   These extremely useful rings have always been difficult to find, now we have them in stock in 2 sizes! Parfocalizing rings are used for several purposes. If you would like to make your non-parfocal eyepiece set parfocal you can put one of these rings on each eyepiece and adjust the height so that all eyepieces are at the same focus point, now when you swap eyepieces you won't need to refocus every time! They are also extremely useful when used with a flip mirror (like the one built into the ETX) for photography. To use a parfocalizing ring with a flip mirror you would first use the telescope focus knob to put your attached camera in perfect focus, now slide a ring over the eyepiece of choice and raise and lower the eyepiece in the holder until it is perfectly in focus. Once you find the focus point that is perfectly matched to the camera slip the ring down and lock it in place using the included wrench. Now you can focus using the eyepiece (much easier than a dim focus screen) and just flip the mirror and take a picture! Leave the ring in place on the eyepiece and you can always quickly and easily pop it back in for photography.

Extender pictured alone (left) and threaded to an eyepiece (right).

ScopeTronix 1.25" Eyepiece Extension

   Ever wish your eyepiece barrel where just little bit longer? Sometimes when using parfocalizing rings or certain photographic equipment, or when eliminating a diagonal your eyepiece may be barely hanging on or simply too short to reach focus. If so these eyepiece extensions are just what you are looking for. They fit any 1.25" eyepiece that has standard filter threads on the bottom. The extension is also threaded for filters. CNC machined from aluminum and anodized black. Internal surfaces are baffled to reduce light reflections. Each adapter is 1" long, fits 1.25" eyepieces with filter threads only.

ScopeTronix 2" Eyepiece Extensions

   Ever wish your eyepiece barrel where just little bit longer? Sometimes when using parfocalizing rings or certain photographic equipment, or when eliminating a diagonal your eyepiece may be barely hanging on or simply too short to reach focus. If so these eyepiece extensions are just what you are looking for. The eyepiece is held in place by a compression ring and then the extension slides into the eyepiece port. Internal surfaces are baffled to reduce light reflections and the extensions are threaded for 48mm filters. Available in three lengths: Small - 1.5", Medium - 2", and Large - 3".

ScopeTronix 2" to 1.25" Adapter

   This adapter allows you to use 1.25" eyepieces in 2" eyepiece ports. Now includes a compression ring to help avoid marring up your expensive eyepieces.

Meade Eyepiece Holder

   The 1.25" eyepiece holder (also known as a visual back) comes standard on the LX90 and the original LX200 telescopes. This adapter will allow you to use 1.25" eyepieces and accessories directly on the back of your SCT. It is also required when attaching the Meade Tele-Extender to the back of an LX200GPS.

ScopeTronix Replacement Rubber Eyeguards

   Lost your eyeguard at the last star party? Misplaced it when you were installing your Digi-T adapter? We now stock replacement rubber eyeguards for your Scopetronix Plossls. These eyeguards will also fit a variety of similar Plossls sold by other manufacturers. This eyeguard will fit eyeguard recesses of ~30mm in diameter.

LensPen, LensPen MiniPro, & DigiKlear

   If you never tried a LensPen you don't know what you're missing. These pens are the ultimate in easy, quick, safe, and spotless cleaning of your eyepieces and other optics. One end has a handy retractable soft brush, the other has a unique liquid free cleaning pad. The cleaning pad is recharged with "dry" cleaning agent each time the cap is replaced. LensPen is excellent for larger eyepieces and finder scopes. LensPen MiniPro is excellent for smaller eyepieces and can get where its big brother can't. The DigiKlear has a curved triangular cleaning pad which is great for use on rectanglar optics such as a digital camera's LCD screen.

ScopeTronix Plugs and Caps
We now carry 3 different sizes of black plastic dust plugs and caps.

ScopeTronix Eyepiece Port Plug:
   These fit any 1.25" opening, such as the ETX eyepiece port. They will also fit the tops of barlows and diagonals, and the eyepiece end of the stock 90mm ETX finder scope.

ScopeTronix Barrel Cap:
   These fit over the bottoms of eyepieces, barlows, and diagonals. They will also fit the front end of the stock 90mm & 125mm ETX finder scope.

ScopeTronix Eyeguard & Finder Cap:
   These will fit the tops of most eyepieces with flip down rubber eyeguards. They fit the Meade 26mm Super Plossl and also fit all of our Plossl eyepieces. These also fit the eyepiece end of the ETX125 right angle finder scope as well.

ScopeTronix "Bolt-Style" Eyepiece Bottles

   The same type of container the Meade Super Plössl's come in. We carry a wide range of sizes to accomodate various eyepieces. Inserts are approx. 9mm thick. All Eyepiece Bottles include 2 foam spacers.

ScopeTronix Optical Storage Boxes

   These plastic storage boxes feature a hinged lid, they snap securely shut and also have a foam pad in the bottom. The small one is just the right size for 1.25" filters while the large one is just the right size for Reducer/Correctors size items.